TECHTONGDA Hand Held Portable Electric Steel Bars Bending Machine 220V 6-22mm

Description: TECHTONGDA Hand Held Portable Electric Steel Bars Bending Machine 220V 6-22mm Pay attention 1. The steel bars must be placed in a horizontal position. After 40-50 continuous bends, please cool them before use (please combine the actual use conditions, such as weather, machine temperature, etc.). 2. After every 300~500 times of bending, tighten the bolts and screws, especially the bolts of the sealing part between the tool holder and the cylinder block. warn: 1. Do not bend steel bars in rain, damp places, places with water, or places where water or oil is likely to enter the bending machine. Moisture will reduce the insulation of the motor, resulting in an electric shock accident. 2 In order to prevent an electric shock accident, please use the power supply through the leakage circuit breaker. In addition, in addition to double insulation, be sure to install a correct ground 'ground'. 3. When using it in the outer frame of pipes, heating appliances, microwave ovens, water tanks, etc., do not let your body touch the grounding 'ground wire'. 4. Please fully keep the workbench and workplace bright, and always pay attention to cleaning and rectification. Scattered places will become the fuse that causes accidents. 5. The bending machine may have rectification sparks during use, and sparks will also occur when the switch is opened and closed. Because it is dangerous to work in places where there are paints, coatings, volatile oils, gasoline, gas, adhesives, etc. that may cause flammable and explosive substances, please never use it. At the same time, be sure to stop using it in closed rooms, tunnels and other places without ventilation. 6. For safety, please wear a helmet and safety shoes with rubber soles. 7. Please use protective goggles to protect your eyes during operation. In addition, in dusty occasions, please use a dust mask and a dust collector at the same time. 8. For the installation of the bending push block and accessories, please use the method of stop gauge at the regular position and use the specified tool to correctly carry out. At the same time, the installed cover and bolts have their own important functions, please do not remove them. 9. Before inserting the plug into the power supply, please confirm whether the switch is disconnected to prevent the bending machine from starting suddenly. 10. Do not transport the bending machine when the plug is connected to the power supply. Do not hang clothes on the switch, it is easy to close the switch by mistake, which will cause an accident. 11. Please always pay attention to the soles of your feet and work in a stable posture. Working in an inappropriate state will bring danger. 12. When the bending machine is found to be in bad condition or abnormal during use, please stop the operation immediately and carry out maintenance. 13. Do not use the bending machine and its accessories beyond the scope of its use, and do not perform excessive operations. Improper operation will not only cause damage to the bending machine, but also be dangerous, please avoid it. 14. When the bending machine is running, please never touch the bending push block and the rotating part, and keep your hands and face away. 15. In order to use it safely and efficiently, please conduct regular inspections. If you need to repair, please do not hand the bending machine to someone who does not have repair knowledge and skills, so please go to the store where you purchased it for inspection and repair. Also, be sure to use the specified parts when replacing parts. Notice: 1. Please use the bending machine with caution. If there is a drop or collision, the frame may be deformed, cracked or damaged. Be sure to fully check before use, and then use it after confirming safety. When it is confirmed that there is an abnormality, please check it immediately. 2. Carrying the product by the lead or pulling the lead out of the socket will damage the lead, resulting in disconnection or short circuit. At the same time, be careful not to let the lead wire come into contact with blades, high-temperature objects, chemicals, etc. If the lead wire is damaged, please stop the operation immediately and carry out inspection. 3. The fan of the bending machine is a necessary part to cool the motor, please do not block it with dust. If it is blocked, it will burn out due to excessive temperature. 4. Please clean up the machine frequently and keep it in the best condition. Especially the motor parts and switch parts, wipe the dust before each use. Also, always clean the lead wire to prevent it from deteriorating due to the action of oil or oily substances. 5. Please check the push block frequently so that it is always used in good condition. 6. This machine has a motor part, so please do not use it in rain or snow. 7. Be sure to tighten the bolts and nuts after every 300-500 bends. Especially the bolts of the sealing part between the head frame and the cylinder block. 8. Please keep the bending machine and accessories in the following places: A. Places out of reach of children. B. Places where temperature and humidity do not change drastically. C. Avoid rain and places with high humidity. D. Places out of direct sunlight. E. Avoid placing it in places prone to fire or explosion and volatile substances. How to use: 1. Please place the length of the bent steel bar on the bottom of the head frame and the push block according to the required length. 2. Clamp the rebar and turn on the switch. 3. The piston moves forward, the steel bar is bent, observe the bending angle with eyes, then release the switch, the motor stops running, pull back the valve handle, and the piston retreats. After purchasing this machine, please read the manual carefully, the relevant precautions are listed in the manual Specifications Voltage；220V Power：1100W Bending time:2-2.5s Minimum rebar size (bent to 90°):18MM Maximum rebar size:22MM Net weight:16kg Note: Do not use the machine to bend rebars that exceed the maximum bending size, after bending dozens of bars, please cool down before use! Item include: Small Portable Portable Electric Bending Machine*1 On Nov 1, 2024 at 02:49:51 PDT, seller added the following information:

Price: 531.1 USD

Location: Rancho Cucamonga, California

End Time: 2024-12-01T18:00:01.000Z

Shipping Cost: 0 USD